All Activity

I have had my 2008 R56 mini tuned for years. Also have a Milltek high flow cat and a jspacer on the downstream O2 (among other mods) . When it comes time for emission in MD I typically clear any codes, complete a full drive cycle (idle, targeted speeds/rpm and sleep as outlined below) then go to emissions before any new codes are thrown. This time my O2 and Evap tests are not ready - after several drive cycles and 200+ regular miles. I am about to throw money at the problem - new upstream O2, new battery (current one is 5+ years old) But thought I would hit pause and see if any of you good people have encountered this issue and have any suggestions The drive cycle requires a mix of city and highway driving under specific conditions. It may need to be repeated a few times to set all monitors, especially the EVAP system. Cold Start & Idle: Start the engine and let it idle for 2 to 3 minutes with all accessories (A/C, headlights, defroster) off. This allows the O2 sensor heaters and other initial systems to be tested. City Driving (Low Speed): Accelerate gently and drive at a steady speed of 20-30 mph for about 3 minutes and 15 seconds. Avoid heavy acceleration or braking. Highway Driving (Steady Speed): Accelerate to and maintain a steady speed between 40-60 mph for about 15 minutes. Using cruise control on a safe, open stretch of road can help maintain a consistent throttle position, which is crucial for the catalyst monitor test. Deceleration (Coasting): Without using the brakes, release the accelerator pedal and coast down to about 20 mph. Repeat this step a few times. Stop & Idle: Bring the vehicle to a complete stop and let it idle for at least 2 minutes. Do not roll through stops. Engine Off/Door Open: Turn the car off, open the driver's door, and close it. Waiting a few minutes allows the car's computer to fully power down and "finalize" the drive cycle data.

I do as well I drive all the way from Glenn Dale Md to get service there because Freddy and Galen are the best!

Many club members take their mini's to GT peace over in Chantilly VA. They are great folks over there and specialize in minis. I have taken my there a few times.

I’m new to The Distrct and am looking for recommendations for my routine service needs. My Cooper S has 71000 miles. Would prefer to avoid mini dealerships. Many thanks!

@1975_mini @TheEnglishBeat

Incredible spec - absolutely perfect color combo. GLWS!

Does anyone know how to look into an order I placed for a new cling for my window back on Nov 27th

So I have these from a purchase for my 2009 mini and I only used them 1 time and then boxed them up, reason being I had a bad wiring harness and the mechanic took them out and I just never installed them again. If anyone would like them please let me know and they will be yours (no charge) honestly I would just like to see them be used, they are a really good set. I uploaded photos.

I just had customized vinyl racing stripes installed on my Clubman by Wrapbeast (wrapbeast.net) in Fairfax. They did a great job. I gave them a photo of what I had in mind (baseball stitching), we discussed options and styles, and they came up with a final design. A very professional and experienced company, and reasonably priced, too. They can do any size/color vinyl design you want. They also do window tinting. I recommend them, located at 3763 Pickett Rd, Fairfax, 703-249-9482.

Thank you very much and I am definitely finding that out and getting adjusted slowly lol but getting more comfortable with her more everyday.

Thank you Corey I really appreciate it can't wait to go on a run and put her through her paces.

Absolutely, I have updated you profile to give you visibility to the additional club forums and events. It is the down time of year but keep an eye out for popup events and the release of the spring schedule Our Membership Coordinator @SusieQ will get your 2026 membership card shipped out in January. Please check your profile and make sure your email and mailing info is up to date.

Congrats

Congrats Scotty! The new dashboard takes some getting used to, but definitely going to be a fun driver for you. Happy Thanksgiving!

Why is it always hard to say goodbye to our cars? lol A very Happy Thanksgiving to you, Evelyn and the family as well!

Thank you very much Lori I will say it was hard saying goodbye to LIL chili because I had done so much to that car but it was time and I really love all the cool stuff in this mini. Can't wait to see you all on the next event. I hope you and your family have a very happy Thanksgiving

WOW! That's a great looking MINI Scotty, congratulations on your new addition!

Just got a new mini today 2023 Cooper s haven't figured out a name yet.

UPDATE - Vibra Techs and the OHLINs coil overs (vs BC Racing that were on there) did the trick. Thanks to Freddy at GT Peace I am back to loving the drive... Rob

I was a member in 2024 and recently purchased a new Mini. Passport Mini stated membership is free for 1 year when you purchase a new vehicle, does that apply to prior members?

Update Request: Please let me know by posting or DM how many people you will have in your party. Event is cross-posted and I need to give the restaurant a head-count. Chillin' stop changed due to Gruto's closing their Purcellville location for the season.

Ordered Vibra-Technics Lower Engine Mount G2 for the lower but your suggestion might help for upper Powerflex site is down but I think I can find them. Thanks

You could use an oem trans mount with the powerflex poly insert that adds more stiffness. Also the yellow poly from powerflex for the engine are not to agressive